Ensuring the security of your valuable possessions is a top priority, and a reliable safe is an essential part of that. Honeywell Safes are designed with user-friendly features that make setup and operation straightforward. This guide will walk you through the essential steps to get your safe up and running efficiently.

Step 1: Install the Batteries

Before you begin using your Honeywell Safe, the first step is to install the batteries. The safe comes with starter batteries, but these should only be used for testing. It's strongly recommended to replace them immediately with new alkaline or lithium batteries for optimal performance.

Important Notes:

• Avoid using non-alkaline or rechargeable batteries as they may not provide consistent power.

How to Install Batteries:

1. Locate the battery compartment cover on the right side of the control panel. Push the cover in and slide it to the right to remove it.

2. Insert four “AA” batteries (not included) into the compartment, making sure the polarity (+ and -) is correct.

3. Once the batteries are installed correctly, the safe will beep, and the LCD readout will flash "GOOD," confirming the installation.

4. Replace the battery compartment cover securely.

Battery Replacement: If the batteries become weak or die, they should be replaced immediately. Follow the same procedure as in Step 1 to replace them. Always remove batteries if the safe will not be used for an extended period to prevent leakage. If the batteries are completely dead and you can't use the digital keypad, use the override key to open the safe and access the battery compartment.

Step 2: Set the Calendar and Clock

With the batteries installed, the next step is to set the calendar and clock on your safe. This feature is crucial for keeping accurate records and for time-sensitive security functions.

How to Set the Calendar and Clock:

1. Ensure the safe door is closed and locked. Press the “” key followed by the “9” key. The LCD readout will glow amber.

2. Enter the year (2 digits), month (2 digits), date (2 digits), and day (1 digit, according to the chart provided in the manual).

3. Next, enter the hour (2 digits) and minutes (2 digits).

4. Once correctly entered, the LCD readout will display the programmed information.

Take note: You must enter all information promptly. If the light goes off during programming, you’ll need to start over.

Step 3: Unlock and Open the Safe

Honeywell Safes feature a dual digital/key lock system for added security. This means you’ll need to enter an active user code to unlock the safe and then use an entry key to open it.

How to Unlock and Open the Safe:

1. Insert the entry key into the cylindrical keyhole on the left side of the control panel.

2. Turn the key counterclockwise as far as it will go.

3. On the keypad, press the “#” key, enter the user code “1 2 3 4,” then press the “#” key again.

4. If the code is correct, “OPEN” will appear on the LCD panel, and you’ll hear a chime indicating the safe is unlocked.

5. Turn the handle upwards to the right (clockwise) within 5 seconds and pull the door open.

To Lock the Safe: Close the door carefully, turn the key clockwise to the right, and remove it. The safe is now securely locked and will require an active user code to open again.

Step 4: Program New User Codes

For enhanced security, it’s essential to change the default factory preset user codes. Honeywell Safes allow you to create two separate reprogrammable active user codes.

How to Program New User Codes:

1. Unlock the safe using the factory preset (or current active) code.

2. If the correct code is entered, "OPEN" will appear on the LCD panel, and you’ll hear a chime.

3. Immediately press the “” key, enter a new 4-8 digit code, and press the “#” key (the “#” key is not needed if using an 8-digit code).

4. If entered correctly, "IN" will appear on the display, followed by a chime. The new code number will briefly appear on the screen.

Repeat the process to reprogram the second factory preset code. Your new codes are now active, and the previous ones have been erased from memory. If you ever need to change your code, simply repeat this process.

To Open the Safe Using the New User Code: Follow the same steps as in Step 3, using your new user code instead of the factory preset code.

Conclusion

Setting up your Honeywell Safe is a simple process that enhances the security of your valuable items. By following these steps, you ensure that your safe operates smoothly and securely. Always remember to use high-quality batteries and keep your user codes private to maintain the integrity of your safe.